Saltar al contenido Saltar al menú de navegación

Tightening Chainsaw Chain

How to Tension Chainsaw Chain

Oregon urges you to become familiar with proper saw chain maintenance techniques, and be aware of the possible dangers which can result if saw chain is not properly maintained. Always wear proper protective apparel when operating or maintaining a chainsaw. Check your chainsaw's chain tension frequently during operation.  

How-To Tension a Chainsaw Chain

Important: Always make sure the engine is turned off before you begin tensioning the chainsaw chain. Also, saw chain should only be tensioned while it is cool, not hot.

Step 1a

Step 1a

Locate the chain tension adjustment points on your chainsaw. Common locations for adjustment points include the side cover and the front of the chainsaw.
Step 1b

Step 1b

For some chainsaw models, like the Oregon CS300, the adjustment points are housed within a side cover release knob.
Step 2

Step 2

Turn the adjustment screw "clockwise" to tighten, "counterclockwise" to loosen.
Step 3a

Step 3a

Adjust the chainsaw chain tension. Use a chainsaw scrench to loosen your tensioning pin. This pin moves the bar for tensioning purposes and is attached to a screw. 

Step 3b

Step 3b

Hold the nose of the bar up as you adjust the tension (do not let go of the bar nose until after you've tightened the mounting nut in).
Step 3c

Step 3c

For sprocket-nose guide bar, follow the solid-nose guide bar instructions, then give the tensioner another quarter to half turn. The bottoms of the lowest tie straps and cutters will come up and solidly contact the bottom of the guide bar rail. The tension for a sprocket-nose guide bar must be tighter than for the solid-nose guide bar.

Step 4

Step 4

As you increase the chain tension, monitor the gap between the under-side of the guide bar and the slack chain. Continue tensioning the saw chain to remove this gap. The saw chain is properly tensioned when the drive links are fully seated into the groove of the guide bar and all chain tie-straps make light contact with the guide bar.
Step 5

Step 5

With a gloved hand, pull the chainsaw chain along the top of the guide bar guide bar away from the engine towards the guide bar nose several times. The chainsaw chain should feel snug but still pull freely.
Step 6

Step 6

Finally, perform a "snap" test to ensure proper saw chain tension. Simply pull the chain on the underside of the guide bar down so one or two drive links are out of the guide bar rails and release it. The chain should snap directly into position. Continue to check the saw chain tension regularly, especially during the first half hour of use. If the chain becomes loose, stop cutting and let the saw cool before readjusting the tension.


Oregon strongly encourages safe work practices and always recommends the use of appropriate safety apparel. Persons demonstrating technical product information in videos or photography do not necessarily represent proper safety habits for any given task.
 

How-To Tension a Chainsaw Chain on an Oregon Intenz Guide Bar

Oregon’s Intenz guide bars have their own built-in tensioning mechanism which allow you to tension chain quickly and easily. With Intenz, you don’t need to hold the bar tip up during the tensioning process.

Step 1

Loosen the bar nuts on the side of the chainsaw guide bar.

Step 2

Insert a screwdriver or chainsaw scrench into the Intenz slot of the guide bar.

Step 3

Turn the screwdriver or scrench clockwise to move the guide bar forward to proper chain tension. Perform a "snap" test to ensure proper saw chain tension.

Step 4

Tighten the chainsaw's guide bar mounting nuts - starting with the back nut before tightening the front. With a gloved hand, pull the chainsaw chain along the top of the guide bar from the engine to the guide bar nose several times. The chainsaw chain should feel snug but still pull freely.

FAQ

How tight should I tension my chain?

A snap test should be performed. Grasp the chain along the bottom of the bar, pull down, and let go. The chain should snap back to its original position, solidly contacting the bottom of the bar rail. For general instructions on how to tension your chain, check out our chain instructional guide and video.  


How do I tighten a chainsaw chain?

A snap test should be performed. Grasp the chain along the bottom of the bar, pull down, and let go. The chain should snap back to its original position, solidly contacting the bottom of the bar rail. For general instructions on how to tension your chain, check out our chain instructional guide and video.  


How much slack should be in a chainsaw chain?

See chain tensioning instructional guide and video for additional information.
 

Related Topics

Saw Chain Terminology

Saw Chain Terminology

By understanding saw chain terminology, you can better maintain and operate your chainsaw.
Finding the Right Saw Chain

Finding the Right Saw Chain

There are several ways to find the right saw chain for your saw. Knowing your make and model of your saw is a good starting point to use our part finder. If you need help identifying this information you can take your saw to a dealer for assistance.
Replacing Chainsaw Chain

Replacing Chainsaw Chain

Get insider tips on how to identify the end-of-life for your saw chain and how to replace it.

Part Finder

Find a full selection of the replacement parts you need with the Oregon Part Finder.

Product Manuals

We want to make sure you can get your job done right. Check out our Product Operations Manuals. 
Volver arriba